Click image to view full size image
ZW86D ON/OFF Contact Fixture Module, 2 way
Introduction
This module is designed to operate in a wall switch box or in locations where the control of an electric device is needed. It is also possible to send a signal to any system that is to be integrated with Z-wave system. Every mains powered Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate "RF dead-spots".
Technical data
Installation
1. Before installation ensure that the voltage supply is disconnected.
2. Connect ZW86 module as shown on above diagram.
3. Place the Module in the switch box.
4. Arrange the antenna (tips are presented as above diagrams)
Do not cut or shorten the antenna - its length is perfectly matched to the band in which the system operates; Locate the antenna as far from metal elements as possible (connecting wires, bracket rings, etc.) in order to prevent interferences.
5. Connect the device in accordance with the wiring diagram presented in Wiring diagram. Switch on 230V of the mains voltage.
6. For "Add" in a network: Put the Z-wave interface controller into "Add" mode, and following its instruction to add the ZW86 to your controller. To get in the "Add" mode, the distance between ZW86 module and controller is suggested to be in one meter. Quickly pressing the learn switch of ZW86 three times or press the mechanical panel K1 three times at least & release to be included. After added in Z-wave network, the indicate LED always lighting.
7. For "Remove" from a network: set up the Z-wave interface controller into "Remove" mode, and following its instruction to delete the ZW86 from your controller. Press the learn switch of ZW86 three times or press the mechanical panel K1 three times at least & release to be excluded. After remove from Z-wave net work indicate LED off.
8. For "Condition" which is controlling other devices of Z-wave system, Condition ensures direct transfer of control commands between devices, and is performed without participation of the main controller. e.g. Dimmer, Switch (ON-OFF), Door/Window sensor, PIR, Shutter or scene (scene may be controlled only through the ZE300 gateway).
Safety and maintenance instruction
- Make sure that all electric connections and connection cables meet the pertaining regulations and are in conformity with the operating instruction.
- Do not overload electrical outlets or extension cords, fire or electric shocks can be the result.
- Please contact an expert in case you have any doubts about the mode of operation, the safety or connecting the appliances.
- Keep all parts away from young children's reach.
- Do not store this item on wet, very cold or warm places, this can damage the electronic circuit boards.
- Avoid dropping or shocks, this can damage the electronic boards.
- Never replace damaged power cables yourself! In such case, remove them from the net and take the devices to a workshop.
- Wireless system are subject to interference from cordless phones, microwaves, and other wireless devices during installation and operation.
Maintenance
The devices are maintenance-free, so never open them. The guarantee becomes void when you open the appliance. Only clean the outside of the devices with a soft, dry cloth or a brush. Prior to cleaning, remove the devices from all voltage source.
Payment&Shipping
About us!
NOTE
Do not use any carboxylic cleaning agents or petrol, alcohol or similar. These will attack the surface of devices. Besides, the vapors are hazardous to your health and explosive. Do not use any sharp edged tools, screw drivers, metal brushes or similar for cleaning.
Warranty 1 year
We are looking forward to your contact!
Introduction
This module is designed to operate in a wall switch box or in locations where the control of an electric device is needed. It is also possible to send a signal to any system that is to be integrated with Z-wave system. Every mains powered Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate "RF dead-spots".
Technical data
| Operating Voltage | 230Vac/60Hz 120VAC/50HZ |
| Operation Temperature | 0 ~ 40ºC |
| Maximum Load | 2000W*2 |
| Electricity consumption | <0.8W |
| Range | 30m line of sight |
| Dimension | 41.9(W)*16.9(H)*36.7(L)MM |
| Net weight | 30g |
| Frequency | 868.42MHz/865.2MHz/869.2MHz/908.42MHz/921.42MHz |
Installation
1. Before installation ensure that the voltage supply is disconnected.
2. Connect ZW86 module as shown on above diagram.
3. Place the Module in the switch box.
4. Arrange the antenna (tips are presented as above diagrams)
Do not cut or shorten the antenna - its length is perfectly matched to the band in which the system operates; Locate the antenna as far from metal elements as possible (connecting wires, bracket rings, etc.) in order to prevent interferences.
5. Connect the device in accordance with the wiring diagram presented in Wiring diagram. Switch on 230V of the mains voltage.
6. For "Add" in a network: Put the Z-wave interface controller into "Add" mode, and following its instruction to add the ZW86 to your controller. To get in the "Add" mode, the distance between ZW86 module and controller is suggested to be in one meter. Quickly pressing the learn switch of ZW86 three times or press the mechanical panel K1 three times at least & release to be included. After added in Z-wave network, the indicate LED always lighting.
7. For "Remove" from a network: set up the Z-wave interface controller into "Remove" mode, and following its instruction to delete the ZW86 from your controller. Press the learn switch of ZW86 three times or press the mechanical panel K1 three times at least & release to be excluded. After remove from Z-wave net work indicate LED off.
8. For "Condition" which is controlling other devices of Z-wave system, Condition ensures direct transfer of control commands between devices, and is performed without participation of the main controller. e.g. Dimmer, Switch (ON-OFF), Door/Window sensor, PIR, Shutter or scene (scene may be controlled only through the ZE300 gateway).
Safety and maintenance instruction
- Make sure that all electric connections and connection cables meet the pertaining regulations and are in conformity with the operating instruction.
- Do not overload electrical outlets or extension cords, fire or electric shocks can be the result.
- Please contact an expert in case you have any doubts about the mode of operation, the safety or connecting the appliances.
- Keep all parts away from young children's reach.
- Do not store this item on wet, very cold or warm places, this can damage the electronic circuit boards.
- Avoid dropping or shocks, this can damage the electronic boards.
- Never replace damaged power cables yourself! In such case, remove them from the net and take the devices to a workshop.
- Wireless system are subject to interference from cordless phones, microwaves, and other wireless devices during installation and operation.
Maintenance
The devices are maintenance-free, so never open them. The guarantee becomes void when you open the appliance. Only clean the outside of the devices with a soft, dry cloth or a brush. Prior to cleaning, remove the devices from all voltage source.
Payment&Shipping
About us!
NOTE
Do not use any carboxylic cleaning agents or petrol, alcohol or similar. These will attack the surface of devices. Besides, the vapors are hazardous to your health and explosive. Do not use any sharp edged tools, screw drivers, metal brushes or similar for cleaning.
Warranty 1 year
We are looking forward to your contact!